Reflections by Sabine Marcelis

Installation, grouting & maintenance

Reflections by Sabine Marcelis is a collection of precision-cut glass tiles, available in FROSTED MATTE and GLOSSY finishes. Colour is applied to the reverse of the glass, creating a consistent appearance with depth, clarity and subtle variations in reflected light. Glass requires careful preparation and installation, particularly regarding moisture, adhesive selection and surface protection. The following guidelines cover the essential steps for installation, grouting and ongoing care.

Before you begin

Glass materialPrecision-cut, reverse-painted glass with a consistent colour layer and delicate surface finishes
Tile formatsAvailable in 10×10, 10×20 and 10×30 cm formats, with bespoke sizes on request
AdhesiveUse a high-performance adhesive specifically suitable for reverse-painted glass tiles
Joint widthA minimum joint width of 2 mm is required to accommodate natural expansion and movement
Surface protectionFROSTED MATTE requires particular care. Remove adhesive and grout residue immediately before drying.
SubstrateA perfectly flat, dry and uniformly coloured substrate is essential for an even finished appearance

Installation guide

PreparationInspect the tiles, check moisture levels and prepare the substrate before installation

Substrate preparation

All substrates must be stable, clean, dry, perfectly flat and free from dust, grease or loose material.

Unevenness, cracks and structural movement must be addressed before installation.

The substrate must be suitable for glass tiles and compatible with the selected adhesive system.

For wet areas, an approved waterproofing system must be installed in accordance with local building regulations.

Moisture control

Moisture behind reverse-painted glass can cause visible marks or discolouration.

Before installation, check the substrate's residual moisture using an appropriate measuring instrument.

A maximum residual moisture level of 2% is specified in the collection guidance. This must be assessed using the correct measurement method for the substrate and adhesive system.

The substrate must be sufficiently dry and fully prepared before the tiles are installed.

Surface colour and preparation

For consistent colour reproduction, use a uniform, opaque and preferably white background.

Apply a suitable primer or surface treatment where required by the adhesive manufacturer.

Avoid uneven colours or visible marks beneath the glass that may affect the finished appearance.

Inspection and layout

Open all boxes before installation and inspect the tiles for damage or irregularities.

Arrange the tiles on a dry surface to establish the layout and achieve balanced alignment.

Plan cuts, corners, trims and transitions carefully before installation begins.

The collection is manufactured to accommodate a 2 mm joint. For example, a nominal 10 cm tile measures approximately 9.8 cm.

InstallationAdhesive selection, tile positioning, spacing and cutting

Adhesive and application

Use a high-performance adhesive specifically approved for reverse-painted glass tiles.

The adhesive must be compatible with the coloured backing of the glass and the intended installation environment.

A light-coloured adhesive is generally preferred to maintain a consistent appearance.

Mix and apply the adhesive strictly according to the manufacturer's instructions. Do not dilute or modify the adhesive unless explicitly permitted.

Apply adhesive evenly using a suitable notched trowel, ensuring complete and uniform coverage behind each tile.

Avoid leaving voids, uneven adhesive marks or trapped moisture behind the glass.

Tile placement

Position each tile carefully, maintaining a minimum joint width of 2 mm.

Use suitable spacers to ensure consistent alignment throughout the installation.

Glass expands and contracts in response to temperature changes, making adequate joint spacing essential.

Do not install tiles with direct edge-to-edge contact.

Maintain suitable movement joints at corners, trims and transitions, following the requirements of the installation system.

Surface protection

Both finishes should be handled carefully during installation.

The FROSTED MATTE surface is particularly delicate and must be protected from adhesive, grout and other installation residue.

Remove any excess adhesive immediately using clean water and a soft sponge before it dries.

Dried adhesive residue may permanently mark the FROSTED MATTE surface.

Avoid abrasive cleaning tools, sharp objects and aggressive chemical products.

Cutting and edges

Glass tiles can be cut using a suitable glass cutter, wet tile saw or diamond blade designed for glass.

For detailed or angled cuts, use an appropriate diamond drill bit with continuous water cooling to prevent excessive heat.

Cut edges may be carefully finished using a suitable fine abrasive designed for glass.

Avoid contact with the visible surface during cutting and finishing.

Always wear protective gloves and eyewear when handling or cutting glass.

Application suitability

Reflections is intended for selected architectural wall applications, subject to the individual project requirements.

A minimum clearance of 3 cm from heat sources, including hobs and fireplaces, is specified in the collection guidance. Suitability must also be confirmed for the temperatures involved.

For wet areas, exterior installations or bespoke applications, the complete installation system must be assessed and confirmed as suitable before installation.

GroutingJoint width, grout selection and careful surface cleaning

Joint width

A minimum grout joint width of 2 mm is required for all Reflections tiles.

Narrower joints are not recommended, as glass requires sufficient space for natural thermal expansion and contraction.

Minor dimensional variations of approximately ±1% may occur.

The tapered edges of the tiles may make the finished grout joints appear slightly wider.

Grout selection

Use a high-quality grout system specifically compatible with glass tiles and the intended application.

Epoxy-based systems are recommended where appropriate for improved performance and colour stability.

Suitable professional systems may include selected products from Mapei, Kerakoll and Litokol, subject to confirmation of compatibility with the glass surface and coloured backing.

Neutral or colour-matched grout is recommended for a consistent, tone-on-tone appearance.

Grouting application

Allow the adhesive to cure fully before grouting, following the manufacturer's recommended drying time.

Ensure that all joints are properly filled to reduce the risk of moisture entering behind the glass.

Apply grout carefully using suitable tools that will not scratch the surface.

Remove excess grout immediately using clean water and a soft sponge, following the grout manufacturer's cleaning procedure.

Do not allow grout residue to dry on the surface, particularly on FROSTED MATTE tiles.

Always test the selected grout and cleaning method on a small area before proceeding with the full installation.

Drying and curing

Glass is non-porous, which can affect the drying and curing conditions of adhesives and grouts.

Allow sufficient curing time according to the selected installation system.

Avoid exposing the tiled surface to water or cleaning products before the grout has fully cured.

Movement joints and sealants

Provide suitable movement joints at corners, perimeter edges and transitions.

Use a compatible flexible sealant where required.

Where silicone is used, select a product specifically suitable for mirrors or reverse-painted glass to avoid damage to the coloured backing.

Follow the sealant manufacturer's instructions regarding application and curing.

Care & MaintenanceCleaning, surface protection and long-term care of glass tiles

Regular cleaning

Clean Reflections tiles using a soft cloth or sponge with water and a mild, pH-neutral cleaning product.

Rinse with clean water and dry with a soft, lint-free cloth where necessary.

Avoid abrasive cleaning tools and products containing strong acids, alkalis or aggressive chemicals.

FROSTED MATTE finish

The FROSTED MATTE finish requires particular care due to its delicate surface.

Use only soft cleaning tools and mild, non-abrasive cleaning products.

Avoid excessive rubbing, abrasive sponges and aggressive cleaning treatments.

Remove spills and surface residue promptly to prevent marks.

GLOSSY finish

Clean the GLOSSY finish using a soft cloth or sponge and a mild, pH-neutral detergent.

Dry with a clean, soft cloth to minimise visible water marks and maintain the reflective surface.

Avoid abrasive materials that may scratch or dull the glass.

Grout and sealant maintenance

Inspect grout joints and flexible sealants periodically, particularly in areas exposed to moisture.

Clean joints gently using a suitable mild cleaning product.

Repair damaged grout or sealant where necessary to maintain the integrity of the installation.

General maintenance

Regular, gentle cleaning is recommended for both finishes.

Avoid steam cleaning, abrasive pads and strong chemical treatments.

Test any new cleaning product on a small, inconspicuous area before use.

Technical informationMaterial properties, available formats and installation requirements

Material: Precision-cut, reverse-painted glass

Collection: Reflections by Sabine Marcelis

Surface: FROSTED MATTE and GLOSSY

Available formats: 10 × 10, 10 × 20 and 10 × 30 cm

Bespoke sizes: Available on request

Dimensional tolerance: Approximately ±1%

Joint width: Minimum 2 mm

Substrate: Stable, perfectly flat, dry and uniformly coloured

Moisture: Maximum 2% residual moisture specified in the collection guidance, subject to the relevant measurement method

Recommended adhesive: High-performance adhesive approved for reverse-painted glass tiles

Grout: High-quality grout suitable for glass; compatible epoxy-based systems recommended

Sealant: Flexible sealant suitable for mirrors or reverse-painted glass

Heat clearance: Minimum 3 cm from heat sources specified in the collection guidance, subject to temperature and application suitability

Surface protection: Immediate removal of adhesive and grout residue, particularly on FROSTED MATTE

Application: Subject to the suitability of the individual installation, substrate and environmental conditions

Important installation note

These guidelines provide general recommendations for the installation and maintenance of reverse-painted glass tiles. Adhesives, grouts, primers, waterproofing systems and sealants must be selected for compatibility with the glass and its coloured backing.

Particular care is required when installing FROSTED MATTE tiles, as dried installation residue may permanently affect the surface.

We recommend consulting a qualified tile installer experienced with architectural glass before beginning the project.

Need guidance?

For questions about installation, grouting or maintenance, our team is available to assist.

Contact us