Milk by Yvonne Koné

Installation, grouting & maintenance

The Milk collection by Yvonne Koné is made from natural terracotta, featuring both glazed and unglazed surfaces. Variations in colour, texture, dimensions and finish are inherent to the material and contribute to the character of each tile. Terracotta is a porous material with water absorption exceeding 10%. Correct preparation, installation and maintenance are essential to ensure a lasting result.

Before you begin

Natural materialVariations in colour, texture and dimensions are natural characteristics of handmade terracotta
Water absorptionTerracotta has a water absorption rate above 10% and requires suitable installation materials and methods
AdhesiveUse a suitable, slow-setting adhesive recommended for highly absorbent terracotta tiles
Joint widthAllow a minimum joint width of approximately 1 mm, adjusted to accommodate natural dimensional variations
Wet areasSuitable installation systems, waterproofing and grouting are essential when using tiles in wet areas
Surface protectionUnglazed terracotta; YV KO 18 Burned, requires sealing to protect its porous surface

Installation guide

PreparationInspect the tiles, plan the layout and prepare the substrate before installation

All substrates must be stable, clean, dry, level and free from dust, grease or loose material before installation.

Any existing cracks, unevenness or structural movement must be addressed before tiling begins.

In wet areas, an approved waterproofing system must be installed in accordance with local building regulations before the tiles are applied.

Planning and layout

Before installation, inspect and arrange the tiles to achieve a balanced distribution of natural colour and surface variations.

We recommend mixing tiles from different boxes during installation to create an even overall appearance.

Check dimensions and plan the layout carefully, allowing for grout joints and necessary movement joints.

InstallationAdhesive selection, tile positioning, spacing and application

Adhesive and application

Due to the high absorbency of terracotta, use a suitable slow-setting adhesive specifically recommended for porous ceramic materials.

Apply the adhesive according to the manufacturer's instructions, ensuring sufficient coverage and proper adhesion to both tile and substrate.

Avoid rapid-setting adhesives unless their suitability has been confirmed by the adhesive manufacturer.

Tile placement

Position each tile carefully, allowing for natural variations in dimensions and thickness.

A minimum joint width of approximately 1 mm is recommended. Wider joints may be necessary depending on the tile format, dimensional variations and installation conditions.

Avoid installing tiles with direct edge-to-edge contact.

Application suitability

The suitability of terracotta tiles for walls, floors and wet areas depends on the specific finish, location and installation system.

Always confirm the intended application before installation.

GroutingJoint width, grout selection and surface protection

General recommendations

Grouting is required for all tiled installations, including wet areas.

Allow the adhesive to cure fully before grouting, following the manufacturer's recommended drying time.

Use a suitable unsanded grout to reduce the risk of scratching or damaging the tile surface.

Glazed terracotta

For glazed tiles, apply grout carefully and remove excess material promptly using a soft sponge and clean water.

Avoid allowing grout residue to dry on the surface.

Do not use abrasive cleaning tools or aggressive chemical cleaners.

Unglazed terracotta

Unglazed tiles, including YV KO 18 Burned, are particularly absorbent and sensitive to staining.

The tiles should be appropriately sealed before grouting to reduce the risk of grout penetration and permanent surface marks.

Use a suitable sealer for porous terracotta, following the manufacturer's recommendations regarding application and drying time.

Movement joints

Movement joints must be incorporated where required by the substrate, room dimensions and installation conditions.

Existing structural movement joints must be continued through the tiled surface.

Use suitable flexible sealants in corners, perimeter joints and other areas subject to movement.

Care & MaintenanceCleaning, sealing and long-term care of glazed and unglazed terracotta

Glazed terracotta

Clean glazed tiles using a soft cloth or sponge with water and a mild, pH-neutral cleaning product.

Avoid acidic or highly alkaline cleaning products, abrasive materials and aggressive chemicals, as these may damage the glaze or grout.

Remove spills and surface residue promptly.

Unglazed terracotta

Unglazed terracotta requires additional care due to its naturally porous surface.

Apply a suitable protective sealer and maintain it according to the manufacturer's instructions.

Clean using a soft cloth and a minimal amount of water with a mild, pH-neutral cleaning product.

Avoid excessive moisture and remove spills immediately to reduce the risk of staining.

General maintenance

Regular, gentle cleaning is recommended for all terracotta surfaces.

Avoid steam cleaning, abrasive pads and strong chemical treatments.

Test any new cleaning or maintenance product on a small, inconspicuous area before use.

Technical informationMaterial properties, water absorption and installation requirements

Material: Natural glazed erracotta

Collection: Milk by Yvonne Koné

Surface: Glazed and unglazed finishes

Water absorption: Above 10%

Recommended adhesive: Suitable slow-setting adhesive for highly absorbent terracotta

Joint width: Minimum approximately 1 mm, adjusted for tile variation and installation conditions

Grout: Suitable unsanded grout

Sealing: Required for unglazed terracotta, including YV KO 18 Burned

Application: Subject to the suitability of the individual tile, substrate and installation system

Important installation note

These guidelines provide general recommendations for the installation and maintenance of terracotta tiles. Installation methods, adhesives, grouts, waterproofing and sealing products must always be selected according to the specific application and local building requirements.

We recommend consulting a qualified tile installer before beginning the project.

Need guidance?

For questions about installation, grouting or maintenance, our team is available to assist.

Contact us