Memories of Amalfi by Onofrio Acone

Installation, grouting & maintenance

Memories of Amalfi by Onofrio Acone is a collection of artisanal terracotta tiles, handcrafted in a family-run workshop near the Amalfi Coast in Italy. Rooted in traditional local craftsmanship, each tile is slowly made by hand using wooden moulds and techniques passed down through generations. The process is deliberately unhurried, allowing the natural character of the clay to remain visible. Subtle variations in colour, dimensions, texture and surface make each tile unique, reflecting the longstanding ceramic traditions of the Amalfi region. The following guidelines cover the essential steps for installation, grouting and ongoing care, with particular consideration for the handmade nature of the tiles.

Before you begin

Natural materialVariations in colour, dimensions and surface are natural characteristics of handcrafted terracotta
Extra tilesWe recommend ordering approximately 10% extra to allow for cuts, selection and installation
AdhesiveUse a suitable professional tile adhesive recommended for terracotta and the intended substrate
Joint widthA joint width of approximately 3 mm is recommended to accommodate natural variations
Suitable applicationsInterior walls and floors. Not recommended for exposed exterior or frost-prone applications
Surface protectionThe glazed surface generally does not require sealing before grouting. Avoid abrasive cleaning products

Installation guide

PreparationInspect the tiles, plan the layout and prepare the substrate before installation

Substrate preparation

All substrates must be stable, clean, dry, level and free from dust, grease or loose material before installation.

Any existing cracks, unevenness or structural movement must be addressed before tiling begins.

In wet areas, an approved waterproofing system must be installed in accordance with local building regulations before the tiles are applied.

Inspection and natural variations

Before installation, inspect all tiles for transport damage or defects that may prevent proper use.

As each tile is handcrafted, variations in colour, dimensions, texture and surface are expected.

These characteristics are inherent to the traditional production process and contribute to the appearance of the finished surface.

Any concerns should be reported to Blēo before installation begins.

Planning and layout

Arrange the tiles on a dry surface before installation to establish the desired composition.

Mix tiles from different boxes to achieve a balanced distribution of colour and natural variations.

Define starting lines and plan the layout carefully to minimise visible cuts and maintain consistent alignment.

We recommend ordering approximately 10% extra tiles to allow for cutting, selection and potential replacements.

InstallationAdhesive selection, tile positioning, spacing and cutting

Adhesive and application

Use a suitable professional tile adhesive recommended for terracotta and the specific installation conditions.

Apply the adhesive evenly to the prepared substrate using an appropriate notched trowel.

Ensure sufficient adhesive coverage and proper contact between the tile and substrate.

Follow the adhesive manufacturer's instructions regarding application, open time and curing.

Tile placement

Position each tile carefully, pressing it firmly into the adhesive to ensure good contact.

Allow for natural variations in dimensions and thickness.

A joint width of approximately 3 mm is recommended to accommodate the handmade characteristics of the tiles.

Use tile spacers where necessary to maintain consistent joints and alignment.

Avoid installing tiles in direct edge-to-edge contact.

Cutting and edges

Tiles can be cut using a suitable tile cutter or wet tile saw fitted with an appropriate diamond blade.

Plan visible cuts and edges in advance to maintain a balanced overall composition.

Handle cut tiles carefully to avoid damage to the surface and edges.

Application suitability

Memories of Amalfi is intended for interior walls and floors, including residential spaces.

For bathrooms and other wet areas, an appropriate waterproofing system must be installed beneath the tiles.

The collection is not recommended for exposed exterior applications or areas subject to frost.

Always confirm the suitability of the selected tile, substrate and installation system before proceeding.

GroutingJoint width, grout selection and surface cleaning

Joint width

A grout joint width of approximately 3 mm is recommended.

The exact width may be adjusted slightly to accommodate natural variations in tile dimensions and achieve consistent alignment.

All joints must be properly filled to create a durable finished surface.

Grout selection

Use a suitable coarse-grained grout recommended for handcrafted terracotta and the intended application.

The grout must be compatible with the tile surface and selected joint width.

We recommend selecting a grout colour close to the tile colour for a consistent appearance.

A contrasting grout may be used to emphasise the geometry of the installation.

Always test the selected grout on a spare tile before proceeding with the full installation.

Grouting application

Allow the adhesive to cure fully before grouting, following the manufacturer's recommended drying time.

Apply grout carefully using a suitable rubber float, ensuring that all joints are completely filled.

Remove excess grout promptly using a soft, damp sponge and clean water.

Work in small sections and avoid allowing grout residue to dry on the tile surface.

Do not use abrasive cleaning tools or aggressive chemical cleaners.

Surface protection

The glazed surface generally does not require sealing before grouting.

However, grout products and installation methods should always be tested on a spare tile to ensure compatibility.

Avoid leaving grout residue on the surface, as dried material may be difficult to remove without damaging the finish.

Movement joints

Movement joints must be incorporated where required by the substrate, room dimensions and installation conditions.

Existing structural movement joints must be continued through the tiled surface.

Use suitable flexible sealants in corners, perimeter joints and other areas subject to movement.

Care & MaintenanceCleaning, surface protection and long-term care of handcrafted terracotta

Regular cleaning

Clean Memories of Amalfi tiles using a soft cloth, sponge or mop with warm water and a mild, pH-neutral cleaning product.

Rinse with clean water where necessary to prevent detergent residue from remaining on the surface.

Avoid abrasive cleaning products, scouring pads, hard brushes and aggressive chemical cleaners.

Surface protection

The glazed surface generally requires no additional sealing under normal interior conditions.

Avoid acidic cleaning products, bleach and other aggressive chemicals that may affect the surface or grout.

Remove spills and residue promptly, particularly in kitchens and other areas exposed to oils or food products.

Grout maintenance

Clean grout joints gently using a soft brush and a suitable mild cleaning product.

Avoid metal brushes and abrasive materials.

Inspect grout joints and flexible sealants periodically, particularly in areas exposed to moisture.

General maintenance

Regular, gentle cleaning is recommended to preserve the appearance and character of the tiles.

Natural variations in colour, texture and surface are inherent to handcrafted terracotta.

Avoid aggressive chemical treatments and abrasive cleaning methods.

Test any new cleaning product on a small, inconspicuous area before use.

Technical informationMaterial properties, joint width and installation requirements

Material: Handcrafted terracotta

Collection: Memories of Amalfi by Onofrio Acone

Origin: Italy, near the Amalfi Coast

Production: Traditionally formed in wooden moulds

Surface: Handcrafted, with natural variations in colour and texture

Tile formats: Selected formats, including 10 × 10 cm

Recommended adhesive: Suitable professional tile adhesive for terracotta

Joint width: Approximately 3 mm, adjusted for natural dimensional variations

Grout: Suitable coarse-grained grout compatible with the tile surface

Extra tiles: Approximately 10% recommended for cuts, selection and replacements

Sealing: Generally not required on the glazed surface

Cleaning: Mild, pH-neutral cleaning products and soft cleaning tools

Suitable applications: Interior walls and floors, subject to the specific installation conditions

Exterior applications: Not recommended for exposed or frost-prone environments

Important installation note

These guidelines provide general recommendations for the installation and maintenance of handcrafted terracotta tiles. Installation methods, adhesives, grouts, waterproofing and cleaning products must always be selected according to the specific application, substrate and local building requirements.

We recommend consulting a qualified tile installer before beginning the project.

Need guidance?

For questions about installation, grouting or maintenance, our team is available to assist.

Contact us