La Bottega by Formafantasma

Installation, grouting & maintenance

La Bottega by Formafantasma is a collection of ceramic tiles produced using the traditional Italian double-firing process, known as bicottura. An industrially manufactured ceramic biscuit is glazed, decorated by spraying and fired a second time at approximately 980°C. The tiles have straight edges, a brushed glazed surface and a thickness of approximately 10 mm. The following guidelines cover the essential steps for installation, grouting and ongoing care.

Before you begin

Ceramic materialDouble-fired glazed ceramic, with subtle variations in colour, decoration and surface
Tile thicknessApproximately 10 mm, with straight edges and traditional ceramic formats
AdhesiveUse a suitable cement-based adhesive for absorbent ceramic tiles, typically C2TE
Joint widthA minimum joint width of 2 mm is recommended, typically 2–3 mm depending on the format
Suitable applicationsInterior walls and domestic floors with normal residential foot traffic
Surface protectionThe glazed surface does not normally require sealing before or after installation

Installation guide

PreparationInspect the tiles, plan the layout and prepare the substrate before installation

Substrate preparation

All substrates must be sound, stable, sufficiently cured, level and free from dust, grease or loose material before installation.

Apply a suitable primer or levelling product where required by the substrate and adhesive system.

Any existing cracks, unevenness or structural movement must be addressed before tiling begins.

In shower areas and other directly wetted surfaces, an approved waterproofing system must be installed in accordance with local building regulations, including correctly detailed corners and penetrations.

Inspection and natural variations

Before installation, inspect all tiles for transport damage or defects that may prevent proper use.

Subtle variations in colour, decoration and surface may occur as part of the production process.

Mix tiles from different boxes to achieve a balanced distribution of these variations across the finished surface.

Any concerns should be reported to Blēo before installation begins.

Planning and layout

Arrange a selection of tiles on a dry surface before installation to establish the desired composition.

Define starting lines and plan the layout carefully to minimise visible cuts and maintain consistent alignment.

Allow for grout joints, perimeter gaps and any necessary movement joints.

Preparing the tiles

When using modern cement-based adhesives, the tiles generally do not require soaking or dampening before installation.

Ensure that the backs of the tiles are clean, dry and free from dust or loose material.

Always follow the adhesive manufacturer's instructions regarding tile preparation.

InstallationAdhesive selection, tile positioning, spacing and cutting

Adhesive and application

For standard interior applications, use a cement-based adhesive suitable for traditional absorbent ceramic tiles.

A C2TE adhesive is generally suitable. A deformable adhesive such as C2TE S1 should be selected where required by the substrate or installation conditions, including underfloor heating.

Professional adhesive systems from Mapei, Kerakoll or equivalent manufacturers may be used according to their technical instructions.

Apply the adhesive evenly using an appropriately sized notched trowel to ensure sufficient contact with the back of each tile.

Back-buttering is recommended where necessary to achieve adequate coverage, particularly for floor installations, larger formats or tiles with a pronounced back profile.

Avoid spot bonding.

Tile placement

Position each tile carefully, pressing it firmly into the adhesive to ensure proper contact.

Use suitable tile spacers to maintain consistent joint widths and alignment.

A minimum joint width of 2 mm is recommended, with approximately 2–3 mm generally suitable depending on the tile format and installation conditions.

Avoid installing tiles with direct edge-to-edge contact.

Cutting and edges

A suitable manual tile cutter may be used for straight cuts.

For more detailed cuts or delicate edges, use a wet tile saw fitted with a fine diamond blade suitable for glazed ceramic.

Support the tile correctly and cut carefully to minimise chipping.

We recommend testing the cutting method on a spare tile before proceeding.

Avoid dry cutting with power tools.

Application suitability

La Bottega is suitable for interior walls and domestic floors with normal residential foot traffic, including living rooms, kitchens and bathrooms.

The collection may also be used for kitchen backsplashes and bathroom wall coverings.

In wet areas, an approved waterproofing system must be installed beneath the tiles.

The suitability of the installation must always be assessed according to the substrate, intended use and exposure to moisture.

GroutingJoint width, grout selection and surface cleaning

Joint width

A minimum grout joint width of 2 mm is recommended.

A joint width of approximately 2–3 mm is generally suitable, depending on the tile format, dimensional variations and intended appearance.

Installation without grout joints is not recommended.

Grout selection

Use a fine-textured cement-based grout suitable for glazed ceramic tiles and the selected joint width.

Unsanded grout may be used where permitted by the grout manufacturer's specified joint-width range.

Grouts containing sand or other aggregates should be tested on a spare tile to ensure they do not scratch or mark the glazed surface.

When using dark or contrasting grout, we recommend a preliminary test to check for staining or residue.

Grouting application

Allow the adhesive to cure fully before grouting, following the manufacturer's recommended drying time.

For standard-setting adhesives, approximately 24 hours may be sufficient, although actual curing times depend on the product and installation conditions.

Apply grout carefully using a suitable rubber float, ensuring that all joints are completely filled.

Remove excess grout within the time specified by the manufacturer using clean water and a soft, well-wrung sponge.

Work in small sections and rinse the sponge frequently.

Do not allow grout residue to harden on the glazed surface.

Movement joints

Movement joints must be incorporated where required by the substrate, room dimensions and installation conditions.

Existing structural movement joints must be continued through the tiled surface.

Use suitable flexible sealants in corners, perimeter joints and other areas subject to movement.

Drying and curing

Always follow the selected adhesive and grout manufacturers' instructions regarding drying and curing.

Regular use and exposure to water should begin only after the adhesive, grout and sealants have reached their specified curing times.

Care & MaintenanceCleaning, surface protection and long-term care of glazed ceramic

Regular cleaning

Clean La Bottega tiles using a soft cloth, sponge or mop with water and a mild, pH-neutral cleaning product suitable for glazed ceramic.

Rinse with clean water where necessary to prevent detergent residue from remaining on the surface.

Avoid abrasive cleaning products, scouring pads, metal brushes and aggressive acidic or alkaline cleaners.

Never use products containing hydrofluoric acid or its derivatives.

Surface protection

The glazed surface does not normally require sealing or additional protective treatment before or after installation.

Waxes and additional surface coatings are unnecessary.

Any sealing requirements for grout joints depend on the selected product and its manufacturer's recommendations.

Cleaning after installation

Remove excess adhesive while fresh and keep joints clear before grouting.

Clean grout residue according to the manufacturer's instructions, using clean water and a soft sponge.

Avoid allowing adhesive or grout residue to harden on the glazed surface.

Do not use metal scrapers or abrasive pads to remove dried residue.

General maintenance

Regular, gentle cleaning is recommended to maintain the appearance of the tiles over time.

Inspect grout joints and flexible sealants periodically, particularly in areas exposed to moisture.

Test any new cleaning product on a small, inconspicuous area before use.

Technical informationMaterial properties, installation requirements and suitable applications

Material: Double-fired brushed glazed ceramic (bicottura)

Collection: La Bottega by Formafantasma

Production: Ceramic biscuit, spray decoration and second firing at approximately 980°C

Surface: Brushed glazed ceramic without a crackle finish

Tile thickness: Approximately 10 mm

Edges: Straight edges

Recommended adhesive: Cement-based adhesive suitable for absorbent ceramic, typically C2TE

Deformable adhesive: C2TE S1 where required by the substrate or installation conditions

Joint width: Minimum 2 mm, typically 2–3 mm

Grout: Fine-textured cement-based grout suitable for glazed ceramic

Sealing: Not normally required on the glazed surface

Cleaning: Mild, pH-neutral cleaning products and soft cleaning tools

Suitable applications: Interior walls and domestic floors with normal residential foot traffic

Wet areas: Suitable subject to an approved waterproofing and installation system

Important installation note

These guidelines provide general recommendations for the installation and maintenance of double-fired glazed ceramic tiles. Installation methods, adhesives, grouts, waterproofing and cleaning products must always be selected according to the specific application, substrate and local building requirements.

We recommend consulting a qualified tile installer before beginning the project.

Need guidance?

For questions about installation, grouting or maintenance, our team is available to assist.

Contact us