Isla by Conie Vallese

Installation, grouting & maintenance

Isla by Conie Vallese is a collection of handmade glazed terracotta tiles produced in Spain. Subtle variations in colour, dimensions, texture and surface are natural characteristics of the material, giving each tile its individual appearance. Careful preparation, installation and maintenance are essential to achieve a balanced and lasting result. The following guidelines cover the principal steps for working with Isla, from substrate preparation and laying to grouting and ongoing care.

Before you begin

Natural materialVariations in colour, texture and dimensions are natural characteristics of handmade terracotta
Extra tilesWe recommend ordering approximately 10% extra to allow for cuts, selection and installation
AdhesiveUse a suitable tile adhesive recommended for glazed terracotta and the intended substrate
Joint widthA joint width of approximately 1–4 mm is recommended, adjusted to accommodate natural variations
Wet areasA suitable waterproofing system, adhesive and grout are essential when installing tiles in wet areas
Surface protectionGlazed terracotta requires gentle handling and cleaning to protect the surface during installation

Installation guide

PreparationInspect the tiles, plan the layout and prepare the substrate before installation

Substrate preparation

All substrates must be stable, clean, dry, level and free from dust, grease or loose material before installation.

Any existing cracks, unevenness or structural movement must be addressed before tiling begins.

In wet areas, an approved waterproofing system must be installed in accordance with local building regulations before the tiles are applied.

Inspection and natural variations

Before installation, inspect all tiles for transport damage or defects that may prevent proper use.

As each tile is handmade, subtle variations in colour, dimensions, texture and surface are expected.

These characteristics are inherent to the production process and contribute to the appearance of the finished surface.

Any concerns should be reported to Blēo before installation begins.

Planning and layout

Arrange the tiles on a dry surface before installation to establish the desired composition.

Mix tiles from different boxes to achieve a balanced distribution of colour and natural variations.

Define starting lines and plan the layout carefully to minimise visible cuts and maintain consistent alignment.

We recommend ordering approximately 10% extra tiles to allow for cutting, selection and potential replacements.

InstallationAdhesive selection, tile positioning, spacing and cutting

Adhesive and application

Use a suitable professional tile adhesive recommended for glazed terracotta and the specific installation conditions.

Apply the adhesive evenly to the prepared substrate using an appropriate notched trowel.

Ensure sufficient adhesive coverage and proper contact between the tile and substrate.

Follow the adhesive manufacturer's instructions regarding application, open time and curing.

Tile placement

Position each tile carefully, pressing it firmly into the adhesive to ensure good contact.

Allow for natural variations in dimensions and surface.

A joint width of approximately 1–4 mm is recommended, depending on the tile format and desired appearance.

Use tile spacers where necessary to maintain consistent joints and alignment.

Avoid installing tiles in direct edge-to-edge contact.

Cutting and edges

Tiles can be cut using a suitable tile cutter or wet tile saw.

Plan visible cuts and edges in advance to maintain a balanced overall composition.

Handle cut tiles carefully to avoid damage to the glazed surface.

Application suitability

The suitability of the tiles for walls, floors, wet areas or exterior applications depends on the specific tile, substrate and installation conditions.

Always confirm the intended application and relevant technical requirements before installation.

GroutingJoint width, grout selection and surface cleaning

Joint width

A grout joint width of approximately 1–4 mm is recommended.

The exact width may be adjusted to accommodate natural variations in tile dimensions and achieve consistent alignment.

All joints must be properly filled to create a durable finished surface.

Grout selection

Use a suitable grout recommended for glazed terracotta and the intended application.

For a calm and unified appearance, we recommend selecting a grout colour close to the tile colour.

A contrasting grout may be used to emphasise the geometry of the installation.

Always test the selected grout on a small area before proceeding with the full installation.

Grouting application

Allow the adhesive to cure fully before grouting. Approximately 24 hours may be sufficient for some systems, but the adhesive manufacturer's recommended curing time must always be followed.

Apply grout using a rubber float, ensuring that all joints are completely filled.

Remove excess grout promptly with a soft, damp sponge and clean water.

Avoid allowing grout residue to dry on the glazed surface.

Do not use abrasive cleaning tools or aggressive chemical cleaners.

Movement joints

Movement joints must be incorporated where required by the substrate, room dimensions and installation conditions.

Existing structural movement joints must be continued through the tiled surface.

Use suitable flexible sealants in corners, perimeter joints and other areas subject to movement.

Care & MaintenanceCleaning, surface protection and long-term care of glazed terracotta

Regular cleaning

Clean Isla tiles using a soft cloth or sponge with warm water and a mild, pH-neutral cleaning product.

Avoid abrasive cleaning tools and products containing bleach, ammonia, solvents or aggressive chemicals, as these may damage the glazed surface.

Rinse with clean water when necessary and remove excess moisture with a soft cloth.

Kitchen surfaces

In kitchens, particularly around worktops and backsplashes, remove oil, grease and food residue promptly.

Prolonged exposure to oils or other substances may temporarily darken sensitive areas of the surface.

Clean gently using a mild, pH-neutral detergent.

Grout maintenance

Clean grout joints using a soft brush and a suitable mild cleaning product.

Avoid hard brushes, steel sponges and abrasive materials.

Inspect grout joints and flexible sealants periodically, particularly in areas exposed to moisture.

General maintenance

With regular care, glazed terracotta will retain its appearance and character over time.

Avoid aggressive chemical treatments and abrasive cleaning methods.

Test any new cleaning product on a small, inconspicuous area before use.

Technical informationMaterial properties, joint width and installation requirements

Material: Handmade glazed terracotta

Collection: Isla by Conie Vallese

Origin: Spain

Surface: Glazed, with natural variations in colour and texture

Dimensions: Available in selected formats, with natural dimensional variations

Recommended adhesive: Suitable professional tile adhesive for glazed terracotta

Joint width: Approximately 1–4 mm, adjusted for tile variation and installation conditions

Grout: Suitable grout recommended for glazed terracotta

Extra tiles: Approximately 10% recommended for cuts, selection and replacements

Cleaning: Mild, pH-neutral cleaning products and soft cleaning tools

Application: Subject to the suitability of the individual tile, substrate and installation system

Important installation note

These guidelines provide general recommendations for the installation and maintenance of handmade glazed terracotta. Installation methods, adhesives, grouts, waterproofing and cleaning products must always be selected according to the specific application and local building requirements.

We recommend consulting a qualified tile installer before beginning the project.

Need guidance?

For questions about installation, grouting or maintenance, our team is available to assist.

Contact us