Terracotta
Installation, grouting, sealing & maintenance
Blēo Essentials Terracotta is a collection of traditional, handmade clay tiles produced in southern Spain. Made from natural clay using established production methods, each tile has its own variations in colour, dimensions, texture and surface. Terracotta is a porous material that requires careful installation and appropriate surface treatment. Depending on the desired appearance, the tiles can be protected with a penetrating sealer or finished using a compatible traditional oil and wax treatment. The following guidelines cover preparation, installation, grouting, sealing and ongoing care of natural, unglazed terracotta.
Before you begin
Installation guide
PreparationInspect the tiles, plan the layout and prepare the substrate before installation
Substrate preparation
The substrate must be stable, sufficiently cured, clean, dry and level before installation begins.
Remove dust, grease, loose material and any substances that may affect adhesion.
Any existing cracks, unevenness or structural movement must be addressed before installation.
In bathrooms, showers and other wet areas, an approved waterproofing system must be installed beneath the tiles according to local building regulations.
Surface sealing does not replace the waterproofing required in wet areas.
Inspection and natural variations
Inspect all tiles before installation for transport damage or defects that may prevent proper use.
As each tile is handmade, variations in colour, texture, dimensions and edges are characteristic of the material.
Mix tiles from several boxes to achieve a balanced distribution of these variations across the finished surface.
Any concerns should be reported to Blēo before installation begins.
Planning and layout
Arrange a selection of tiles on a dry surface before installation to establish the intended composition.
Define starting lines and plan the layout carefully to minimise visible cuts and accommodate dimensional variations.
We recommend ordering approximately 10% extra tiles to allow for cutting, selection and potential replacements.
Store the tiles in their original packaging in a clean, dry environment before installation.
Preparing the tiles
Terracotta is naturally absorbent. Before installation, ensure that the tiles are clean and free from loose dust.
Follow the selected adhesive manufacturer's recommendations regarding any necessary preparation of the tile backs.
Where a pre-installation treatment is recommended by the chosen protective system, test it on a spare tile and ensure that it does not affect adhesion.
InstallationAdhesive selection, tile positioning, spacing and cutting
AAdhesive and application
Use a high-quality professional adhesive suitable for porous terracotta and the specific installation conditions.
A suitable flexible cement-based adhesive may be used where recommended for the substrate, tile format and intended application.
Apply adhesive evenly using an appropriately sized notched trowel.
For floor installations, back-buttering may be necessary to achieve adequate adhesive coverage and support.
Avoid spot bonding and unsupported areas beneath the tiles.
Always follow the adhesive manufacturer's instructions regarding application, open time and curing.
Tile placement
Position each tile carefully, pressing it firmly into the adhesive to ensure proper contact.
Allow for natural differences in thickness, dimensions and edge profiles.
A joint width of approximately 3–5 mm is recommended as a starting point for handmade terracotta.
The exact width should be adjusted according to tile format, dimensional variations and installation conditions.
Use suitable spacers where necessary to maintain alignment.
Avoid installing tiles in direct edge-to-edge contact.
Cutting and edges
Terracotta can be cut using a suitable tile cutter or wet tile saw fitted with an appropriate diamond blade.
Work carefully to minimise chipping and damage to the edges.
Cut tiles should be cleaned and allowed to dry before any required protective treatment.
Application suitability
Blēo Essentials Terracotta can be used for interior walls and floors, subject to the selected tile format, installation system and intended use.
In kitchens and bathrooms, appropriate surface protection is important due to exposure to moisture, oils and everyday staining.
Wet areas require an approved waterproofing system beneath the tiles.
Exterior and frost-exposed applications require separate technical confirmation of suitability.
GroutingJoint width, grout selection and protection of the porous terracotta surface
Joint width
A grout joint width of approximately 3–5 mm is generally recommended for handmade terracotta.
The exact width may be adjusted to accommodate variations in dimensions and edges.
All joints must be properly filled to create a durable finished surface.
Grout selection
Use a grout suitable for porous terracotta and the selected joint width.
The grout must be compatible with the surface treatment and intended installation conditions.
A grout colour close to the natural terracotta will create a more continuous appearance, while contrasting grout can emphasise the geometry of the layout.
Dark or strongly pigmented grout should always be tested on a spare tile before installation.
Protection before grouting
Unglazed terracotta is highly absorbent and can take up pigments and moisture from grout.
Before grouting, we recommend applying a suitable penetrating pre-sealer or grout-release treatment designed for natural terracotta.
This helps reduce staining and makes grout residue easier to remove.
The treatment must be compatible with the intended final finish and must not interfere with grout adhesion.
Allow the pre-sealer to cure according to the manufacturer's instructions before grouting begins.
Always test the complete treatment on spare tiles before proceeding.
Grouting application
Allow the adhesive to cure fully before grouting.
Apply grout carefully using a suitable rubber float, ensuring that all joints are completely filled.
Remove excess grout promptly using clean water and a soft, well-wrung sponge.
Work in small sections and avoid allowing grout residue to dry on the tile surface.
Do not use acidic cement-residue removers, abrasive pads or aggressive cleaning products unless specifically approved for the terracotta and its surface treatment.
Movement joints
Movement joints must be incorporated where required by the substrate, room dimensions and installation conditions.
Existing structural movement joints must be continued through the tiled surface.
Use suitable flexible sealants at corners, perimeter joints and other areas subject to movement.
Care & MaintenanceSealing, traditional finishes, cleaning and long-term protection of natural terracotta
Final sealing
Once installation and grouting are complete, allow the tiles and joints to cure and dry fully.
Apply a suitable penetrating sealer specifically developed for porous terracotta.
A penetrating sealer helps reduce water and oil absorption while maintaining the natural appearance of the material.
Depending on the absorbency of the tiles and the selected product, more than one application may be necessary.
Remove excess product according to the manufacturer's instructions to prevent unwanted surface residue.
Sealing reduces absorption but does not make terracotta completely waterproof or stain-proof.
Natural matte finish
For a natural appearance, we recommend a suitable impregnating sealer designed to preserve the colour and texture of unglazed terracotta.
This type of treatment generally provides protection without creating a pronounced surface coating.
The final appearance depends on the sealer and the natural absorbency of the clay.
Test the treatment on a spare tile before applying it to the complete surface.
Traditional oil and wax finish
Terracotta can also be treated using traditional oil and wax systems, where suitable for the intended application.
A compatible oil treatment can deepen the natural colour of the clay, bringing out warmer red, orange and brown tones.
A suitable finishing wax may then be applied as part of the same approved treatment system to provide additional surface protection and a softer sheen.
Oil and wax treatments generally require more regular maintenance than modern penetrating sealers.
They may also be unsuitable for certain wet areas or demanding floor applications.
Use only products specifically recommended for terracotta and follow the manufacturer's complete application and maintenance instructions.
Do not combine penetrating sealers, oils and waxes unless their compatibility has been confirmed.
Regular cleaning
Clean terracotta using a soft cloth or mop with warm water and a mild, pH-neutral cleaner suitable for natural terracotta.
Avoid acidic cleaning products, abrasive powders, strong alkaline cleaners and aggressive chemicals.
Remove oil, grease and liquid spills promptly to reduce the risk of staining.
Avoid leaving standing water on the surface unnecessarily.
Ongoing maintenance
The frequency of maintenance depends on the selected treatment, location and level of use.
Penetrating sealers may require periodic reapplication as their protective performance diminishes.
Traditional oil and wax treatments may require more frequent care to maintain their appearance and protective qualities.
Always follow the maintenance instructions provided by the treatment manufacturer.
Before applying a new protective product, confirm its compatibility with any existing treatment.
Technical informationMaterial properties, installation requirements and surface treatment
Material: Natural handmade terracotta
Collection: Blēo Essentials Terracotta
Origin: Southern Spain
Production: Traditional clay tile manufacturing
Surface: Natural, unglazed terracotta
Appearance: Variations in colour, dimensions, texture and edges
Porosity: Naturally absorbent
Recommended adhesive: Professional adhesive suitable for porous terracotta and the intended substrate
Joint width: Approximately 3–5 mm, subject to format and installation conditions
Grout: Suitable professional grout for porous terracotta
Pre-grouting protection: Compatible penetrating pre-sealer or grout-release treatment
Final protection: Suitable terracotta impregnating sealer or approved traditional oil and wax system
Cleaning: Mild, pH-neutral cleaning products and soft cleaning tools
Suitable applications: Interior walls and floors, subject to the installation system
Wet areas: Require appropriate waterproofing and compatible protective treatment
Exterior applications: Subject to separate technical confirmation
Maintenance: Periodic renewal of the protective treatment according to use and manufacturer instructions
Important installation note
These guidelines provide general recommendations for the installation, sealing and maintenance of handmade terracotta tiles.
As a natural, porous material, terracotta may respond differently to adhesives, grouts, sealers, oils and waxes.
Always test the complete installation and protective treatment system on spare tiles before proceeding.
Installation methods and products must be selected according to the specific project, substrate, intended application and local building requirements.
We recommend consulting a qualified tile installer experienced with traditional terracotta before beginning the project.
Need guidance?
For questions about installation, grouting or maintenance, our team is available to assist.