Core Zellige by Muller Van Severen

Installation, grouting & maintenance

Core Zellige by Muller Van Severen is handcrafted and individually glazed in Morocco. Variations in colour, texture, dimensions and thickness are inherent to the material and contribute to the character of each tile. Traditional zellige requires careful preparation and installation to accommodate its irregular surfaces and edges. The following guidelines cover the essential steps for installation, grouting and ongoing care.

Before you begin

Natural materialVariations in colour, glaze, dimensions and thickness are natural characteristics of handmade zellige
AdhesiveUse a high-quality, flexible adhesive suitable for handmade zellige and the intended substrate
Wet areasA suitable waterproofing system, adhesive and grout are essential when installing zellige in wet areas
Tile thicknessApproximately 10–14 mm, with natural variations between individual tiles
Joint widthNarrow joints of approximately 0-1 mm are recommended, adjusted to accommodate irregular edges
Surface protectionGlazed zellige generally requires no surface sealing. Grout and exposed porous areas may require additional protection depending on the application

Installation guide

PreparationInspect the tiles, plan the layout and prepare the substrate before installation

Substrate preparation

All substrates must be stable, clean, dry, level and fully cured before installation.

Remove dust, grease, loose material and any substances that may affect adhesion.

Any existing cracks, unevenness or structural movement must be addressed before tiling begins.

In wet areas, an approved waterproofing system must be installed in accordance with local building regulations before the tiles are applied.

Inspection and natural variations

Before installation, inspect all tiles for transport damage or irregularities beyond the expected characteristics of handmade zellige.

Core Zellige is individually crafted and glazed, resulting in natural variations in colour, thickness, dimensions and surface texture.

Small chips, uneven edges and subtle variations in the glaze are characteristic of the production process.

Any concerns should be reported to Blēo before installation begins.

Planning and layout

Mix tiles from several boxes before installation to achieve a balanced distribution of colour and surface variations.

We recommend laying out a selection of tiles in advance to establish the desired arrangement.

Allow for natural dimensional differences, narrow grout joints and any necessary movement joints.

InstallationAdhesive selection, tile positioning, spacing and cutting

Adhesive and application

Use a high-quality, flexible tile adhesive suitable for handmade zellige and the intended substrate.

Due to variations in thickness and the uneven backs of the tiles, adhesive consumption may be approximately 1.5–2 times higher than for standard ceramic tiles.

A 10–12 mm notched trowel can be used as a starting point, depending on the substrate and adhesive manufacturer's recommendations.

Apply adhesive evenly to the substrate and, where necessary, to the back of each tile to ensure sufficient contact and support.

Avoid leaving voids behind the tiles.

Preparing the tiles

Before installation, remove dust and loose residue from the tile surfaces and backs.

For traditional glazed zellige, pre-soaking in clean water for approximately five minutes may be appropriate to reduce excessive moisture absorption from the adhesive.

Allow excess water to drain before installation.

Always confirm the recommended pre-wetting method with the adhesive manufacturer, as some modern adhesive systems require different preparation.

Tile placement

Install each tile individually, adjusting its position to accommodate variations in dimensions and thickness.

Traditional zellige is typically installed with narrow, minimally visible joints.

A joint width of approximately 1 mm is recommended, although slight adjustments may be necessary to accommodate individual tiles.

The finished surface will naturally have subtle variations in level and alignment. These characteristics are part of the material's appearance.

Use suitable spacers or wedges where necessary to achieve a balanced installation.

Cutting and edges

Use a suitable diamond-blade wet saw or tile cutter for precise cuts.

Handle cut tiles carefully, as edges may be sharp or uneven.

Plan visible edges and corners in advance to ensure a consistent finish.

Application suitability

Core Zellige is suitable for interior wall applications, including kitchens, bathrooms and living areas.

For wet areas, use an approved waterproofing system and installation materials suitable for the intended environment.

Floor, exterior and other specialised applications must be assessed individually and confirmed as suitable before installation.

GroutingJoint width, grout selection and surface protection

Joint width

Core Zellige is traditionally installed with narrow, minimally visible joints.

A joint width of approximately 1 mm is commonly used, although natural variations in tile dimensions may create slightly wider gaps.

All joints and gaps must be properly filled with grout to protect the edges and create a durable surface.

Grout selection

Use a high-quality, fine-grained grout suitable for handmade glazed zellige and the intended application.

We recommend selecting a grout colour close to the tile colour to create a consistent appearance across the surface.

Contrasting grout may emphasise variations in tile dimensions and irregular edges.

The selected grout must be suitable for the joint width and installation conditions.

For wet areas, use a grout system specifically approved for the intended environment.

Grouting application

Allow the adhesive to cure fully before grouting, following the manufacturer's recommended drying time.

Apply grout carefully across the surface, ensuring that all joints, gaps and natural irregularities are filled.

Work in small sections and remove excess grout promptly with a soft, damp sponge.

Avoid allowing grout residue to dry on the glazed surface.

Test the selected grout on a small area before proceeding with the full installation.

Movement joints

Movement joints must be incorporated where required by the substrate, room dimensions and installation conditions.

Existing structural movement joints must be continued through the tiled surface.

Use suitable flexible sealants in corners, perimeter joints and other areas subject to movement.

Care & MaintenanceCleaning, surface protection and long-term care of glazed zellige

Regular cleaning

Clean Core Zellige using a soft cloth or sponge with water and a mild, pH-neutral cleaning product.

Avoid abrasive cleaning tools, acidic products and aggressive chemical cleaners, as these may affect the glaze or grout.

Remove spills and surface residue promptly.

Surface protection

The glazed surface of Core Zellige generally does not require sealing for standard interior wall applications.

However, grout joints, natural surface irregularities and exposed porous areas may benefit from a suitable protective treatment.

In wet areas, additional protection may be necessary depending on the installation system and level of water exposure.

Always test sealing products on a small, inconspicuous area before application.

Natural characteristics

Subtle variations in colour, texture and glaze are natural characteristics of handmade zellige.

Small chips, irregular edges and variations in surface reflection are part of the material's appearance.

These characteristics should not be treated as defects or corrected using abrasive methods.

General maintenance

Regular, gentle cleaning is recommended to preserve the appearance of the tiles.

Avoid steam cleaning, abrasive pads and strong chemical treatments.

Inspect grout joints and flexible sealants periodically, particularly in areas exposed to moisture.

Technical informationMaterial properties, dimensions and installation requirements

Material: Handmade Moroccan zellige

Collection: Core Zellige by Muller Van Severen

Surface: Individually glazed, with natural variations in colour and texture

Tile thickness: Approximately 10–14 mm

Dimensional variation: Approximately 2–3 mm

Recommended adhesive: High-quality, flexible adhesive suitable for handmade zellige

Adhesive consumption: Approximately 1.5–2 times standard ceramic tile consumption, depending on the installation

Notched trowel: Approximately 10–12 mm, depending on substrate and adhesive system

Joint width: Approximately 1 mm, adjusted for natural dimensional variations

Grout: Fine-grained grout suitable for glazed zellige

Sealing: Generally not required on glazed surfaces; grout and porous areas may require protection

Application: Interior walls, including kitchens, bathrooms and living areas. Other applications subject to individual assessment.

Important installation note

These guidelines provide general recommendations for the installation and maintenance of handmade zellige. Installation methods, adhesives, grouts, waterproofing and sealing products must always be selected according to the specific application and local building requirements.

We recommend consulting a qualified tile installer before beginning the project.

Need guidance?

For questions about installation, grouting or maintenance, our team is available to assist.

Contact us